FLASH AXIOO PICOpad 7H BOOTLOOP / DEAD BOOT

Brand     : AXIOO
ProdName  : PICOpad 7H
ProdModel : PICOpad 7H(GGF1)
Device    : PICOpad 7H
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.KK1.MP7.V1.44
FLASH AXIOO PICOpad 7H BOOTLOOP / DEAD BOOT

FIRMWARE BUAT MTK 6572

  Bahan:

1. FIRMWARE MTK 6572 DOWNLOAD STOCK ROM AXIOO PICOpad 7H 4.4.2 atau Download Disini
2. FLASH TOOL DOWNLOAD DISINI
3. Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Axioo 7H yang lain

1. BUAT AXIOO PICOpad 7H MT6582 KELINK INI
2. BUAT Axioo Picopad S1 atau 7H GGB MT6582

Start  at : [12/25/2015 / 10:19:01 PM]
Operation : Check / Read Info [ v1.39 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : FE014E4D4D433038473F00400015AFB5
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 00FE , OEM : 014E
[eMMC] : FLASH_INF : [MICRON] , G80CM
[eMMC] : FLASH_CID : FE014E4D4D433038473F00400015AFB5
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000001D5000000
[eMMC] : FLASH_UCP : 7504 MiB
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : AXIOO
ProdName  : PICOpad 7H
ProdModel : PICOpad 7H(GGF1)
Device    : PICOpad 7H
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.KK1.MP7.V1.44

MODEM :
BaseBand  : MT6572_S00_MOLY_WR8_W1315_MD_WG_MP_V72_1_wg_n

EXTRA :
LCD [0] : $(ROCO_CUST_LCM)
LCD Res : $(ROCO_LCM_HEIGHT)x$(ROCO_LCM_WIDTH)
TOUCH [0] : $(ROCO_TP)
CAM [0] : $(ROCO_MAIN_CAM)
CAM [1] : $(ROCO_SUB_CAM)
MODEM : TS_SIM2_3G_900
LOCALE : $(ROCO_LANGUAGE)

Done!
Elapsed: 00:00:13

Start  at : [12/25/2015 / 10:58:54 PM]
Operation : Read Flash [ v1.39 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : FE014E4D4D433038473F00400015AFB5
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 00FE , OEM : 014E
[eMMC] : FLASH_INF : [MICRON] , G80CM
[eMMC] : FLASH_CID : FE014E4D4D433038473F00400015AFB5
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000001D5000000
[eMMC] : FLASH_UCP : 7504 MiB
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ...

Brand     : AXIOO
ProdName  : PICOpad 7H
ProdModel : PICOpad 7H(GGF1)
Device    : PICOpad 7H
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.KK1.MP7.V1.44

[Read Ok] : preloader_w706.bin
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img
[Read Ok] : fat.img

[ScatCFG] : MT6572 / V1.1.1 / w706 / EMMC
FW Size : 933 MiB
Scatter saved to : G:\andro3\axioo\MT6572__AXIOO__PICOpad_7H(GGF1)__PICOpad_7H__4.4.2__ALPS.KK1.MP7.V1.44\

All done!

Done!
Elapsed: 00:05:25